Suppose in the example above, you determine that the arrows will need to land 1″ higher and 2″ to the right for a perfect bulls-eye. Step two:Īpproach your target and estimate how many inches your arrow group would need to move up and to the right for all the arrows to have hit the bulls-eye. Suppose this is what you see:Īs you can see, the three arrows landed in a pretty tight group, but they are a little to the left and bottom relative to where they should have landed (the bulls-eye). Repeat these steps 3 times, shooting a total of three arrows. Squeeze the trigger quickly but use only the tip of your index finger to do so (don’t move your entire palm or arm as it will ruin your accuracy). Cock the crossbow using a rope or crank aid (if you don’t have one, I recommend the Jandao extra-long rope), seat an arrow, and align the top-most red dot or reticle in your scope with the bulls-eye. Stand exactly 20 yards away from your target. Shooting aid or not, let’s get down to business. However, if you do not have access to one, then it’s not a problem at all your results might be a little less accurate, but it will still be more than enough to get excellent performance out of your crossbow. This will allow you to sight your crossbow perfectly, and most decent shooting ranges should have such aids available. A shooting aid is basically anything that “fixes” your crossbow so that the weapon does not move at all as you pull the trigger. It is recommended that when you attempt to sight your crossbow that you use some form of shooting aid. Step By Step: Sighting Your Crossbow (With Pictures) Should your crossbow scope use different values per click, it will be clearly mentioned in the instruction booklet that came with your package. For the vast majority of scopes, it is as follows:ġ click = 1/4″ adjustment at a 100 yard distance. Adjustment Knob “Clicks”Īs you turn the elevation/windage knobs, you will hear a “click.” Each click represents a certain unit of adjustment being made (measured in M.O.A, or Minutes Of Angle). Once you are finished making adjustments, don’t forget to put the protective caps back on. Keep in mind that you’ll need a screwdriver or a coin to turn the knobs, so make sure you carry one with you in the field. The picture on the right shows windage adjustments, and you’ll turn it clock-wise for “right” and anti-clockwise for “left.” Once you remove the caps, you’ll see this:Īs you can see, there are markings on each knob signifying the direction you need to turn the knob to achieve adjustments in a particular plane the left-most picture shows elevation adjustments, and you will need to turn it clockwise (as the “up” arrow indicates) to raise the arrow point-of-impact, and anti-clockwise to lower it. These adjustment knobs are covered with protective plastic caps, which you’ll need to remove to actually make elevation and windage adjustments. Windage adjustment knob: this will be located on the side of your scope, and allows you to adjust arrow point-of-impact left and right.Įlevation adjustment knob: located at the top of your scope, it allows you to adjust arrow point-of-impact up and down. There are two knobs on every scope which you’ll be using to sight your crossbow: See pictures below to understand what distance each dot/reticle is for. By “zero” we simply mean that you must make sure the top dot or reticle is properly aligned for hitting targets from the 20 yard distance once you do this, the remaining dots and reticles will be automatically aligned for their respective distances. Your goal is to “zero” the top-most reticle or dot for a specific distance (20 yards in almost all cases unless instructed otherwise by the crossbow manufacturer). The basic procedure is exactly the same for any scope you get, although you should check out our best crossbow recommendations to make sure the scope that comes with your crossbow has decent optics. The exact procedure for sighting a crossbow will vary slightly from scope to scope, as different models can have somewhat different adjustment knobs. The process of sighting a crossbow is very easy, though if you’re a beginner who’s never done it before you might assume otherwise. Also, please see our arrow drop interactive chart to get a feel for how differences in arrow weight will impact trajectory. You will not be able to properly sight your crossbow if you aren’t capable of shooting tight groups of arrows from a 20 yard distance “tight groups” means that arrows should be landing very close to each other – a spot around 2-3 inches across – regardless of whether they are landing in the bulls-eye or not. Important Note: if you are a rank beginner, we strongly recommend that you shoot 50-100 arrows before attempting to sight your scope.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |